收藏本站
25A512
2.12
RELEASE FROM DEEP
Release from Deep Power-Down mode and Read
POWER-DOWN AND READ
ELECTRONIC SIGNATURE
Once the device has entered Deep Power-Down
mode all instructions are ignored except the Release
from Deep Power-down and Read Electronic Signa-
ture command. This command can also be used when
the device is not in Deep power-down to read the
electronic signature out on the SO pin unless another
command is being executed such as Erase, Program
or Write Status Register.
Electronic Signature is entered by driving CS low,
followed by the RDID instruction code (Figure 2-12)
and then a dummy address of 16 bits (A15-A0). After
the last bit of the dummy address is clock in, the 8-bit
Electronic Signature is clocked out on the SO pin.
After the signature has been read out at least once,
the sequence can be terminated by driving CS high.
The device will then return to Standby mode and will
wait to be selected so it can be given new instructions.
If additional clock cycles are sent after the electronic
signature has been read once, it will continue to output
the signature on the SO line until the sequence is
terminated.
FIGURE 2-12:
CS
RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE
0
1
2
3
4
5
6
7
8
9 1 0 11
2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1
SCK
Instruction
16-bit Address
SI
1
0
1
0
1
0
1
1 15 14 13 12
2
1
0
High-Impedance
Electronic Signature Out
SO
7
0
6
0
5
1
4
0
3
1
2
0
1
0
0
1
Manufacturer’s ID = 0x29
Driving CS high after the 8-bit RDID command but before the Electronic Signature has been transmitted will still ensure
the device will be taken out of Deep Power-Down mode. However, there is a delay T REL that occurs before the device
returns to Standby mode (I CCS ), as shown in Figure 2-13.
FIGURE 2-13:
CS
RELEASE FROM DEEP POWER-DOWN
0
1
2
3
4
5
6
7
T REL
SCK
Instruction
SI
1
0
1
0
1
0
1
1
High-Impedance
SO
? 2010-2011 Microchip Technology Inc.
Preliminary
DS22237C-page 19
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
25AA020A-I/MS IC EEPROM 2KBIT 10MHZ 8MSOP
25AA02E48-I/SN IC EEPROM 2KBIT 10MHZ 8SOIC
25AA080C-I/MS IC SRL EEPROM 1KX8 1.8V 8-MSOP
25AA1024T-I/MF IC EEPROM 1MBIT 20MHZ 8DFN
25AA160C-I/P IC SRL EEPROM 2KX8 1.8V 8-PDIP
25AA512T-I/MF IC EEPROM 512KBIT 20MHZ 8DFN
25C040X/ST IC EEPROM 4KBIT 3MHZ 8TSSOP
25C080-I/P IC EEPROM 8KBIT 3MHZ 8DIP
相关代理商/技术参数
25A512ISN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25A512IST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25A512T-I/SN 功能描述:电可擦除可编程只读存储器 512k 64K X 8 1.8V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25A512T-I/ST 功能描述:电可擦除可编程只读存储器 512k 64K X 8 1.8V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
25A512TISN 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25A512TIST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25A6 制造商:未知厂家 制造商全称:未知厂家 功能描述:PENTODE POWER AMPLIFIER
25-A659-00-00NP 制造商:Sumida Corporation 功能描述:- Bulk